[sclug] USB card won't come out to play
Neil Haughton
n.a.haughton at bigfoot.com
Sun Oct 30 20:25:46 UTC 2005
Alex Butcher wrote:
> On Sun, 30 Oct 2005, Neil Haughton wrote:
>
>> Can anyone help with a little problem that is teasing me at the moment?
>>
>> My motherboard has USB2 build in, but I've used all 4 ports and need
>> some more. I picked up a PCI USB1.1 card (fine for mouse and
>> printer) on the cheap at Maplins, and I thought I could just plug it
>> in and I'd be away. But no, the card just isn't recognised. I've
>> checked the BIOS to see if there is something to switch on or off,
>> and the only thing I could find was Legacy USB support, which I
>> enabled. No improvement - the ports aren't even shown in USBView.
>>
>> Can anyone tell me what's wrong?
>
>
> Not yet, my crystal ball is on the blink.
>
>> What have I missed?
>
>
> Lots of useful information you could have told us, like:
>
> - which distro are you running?
Mandriva 2005LE
> - do you have all the updates for that distro installed?
Yes
> - what's the version of the kernel you're using?
2.6.11
> - what does dmesg say after booting?
See attached file - I haven't edited it in case I drop something useful
> - what kernel modules do you have loaded?
See attached file.
> - what chipset is used on the USB1.1 card?
Looks like VIA181D (but the print on the chip is very small, so I may
not have that exactly correct.
> - have you tried plugging some USB-powered device in? Does it indicate
> that
> it's getting power?
Yes. My optical mouse usually glows red, but it's lifeless plugged into
this card. However I can charge my little Mustek Gsmart Mini digicam
from it.
> - have you tried using the card with any other OS on the system? Did
> it work
> there?
>
Tried with WinXP, which doesn't recognise it either. The card doesn't
come with any special Windows drivers.
HTH!
Neil.
-------------- next part --------------
Module Size Used by
ipt_TOS 1888 12
ipt_REJECT 5600 4
ipt_pkttype 1248 4
ipt_LOG 6208 8
ipt_state 1376 6
wacom 11616 0
ipt_multiport 2144 0
ipt_conntrack 1984 0
iptable_mangle 2080 1
ip_nat_irc 1568 0
ip_nat_tftp 1280 0
ip_nat_ftp 2272 0
iptable_nat 19068 3 ip_nat_irc,ip_nat_tftp,ip_nat_ftp
ip_conntrack_irc 70384 1 ip_nat_irc
ip_conntrack_tftp 3056 1 ip_nat_tftp
ip_conntrack_ftp 71344 1 ip_nat_ftp
ip_conntrack 37400 9 ipt_state,ipt_conntrack,ip_nat_irc,ip_nat_tftp,ip_nat_ftp,iptable_nat,ip_conntrack_irc,ip_conntrack_tftp,ip_conntrack_ftp
iptable_filter 2144 1
ip_tables 18176 10 ipt_TOS,ipt_REJECT,ipt_pkttype,ipt_LOG,ipt_state,ipt_multiport,ipt_conntrack,iptable_mangle,iptable_nat,iptable_filter
md5 3648 1
ipv6 232320 10
snd-seq-dummy 2596 0
snd-seq-oss 31584 0
snd-seq-midi-event 6208 1 snd-seq-oss
snd-seq 47472 5 snd-seq-dummy,snd-seq-oss,snd-seq-midi-event
snd-pcm-oss 49056 0
snd-mixer-oss 17248 1 snd-pcm-oss
snd-via82xx 23040 0
snd-ac97-codec 75256 1 snd-via82xx
snd-pcm 80776 3 snd-pcm-oss,snd-via82xx,snd-ac97-codec
snd-timer 20324 2 snd-seq,snd-pcm
snd-page-alloc 7588 2 snd-via82xx,snd-pcm
gameport 3328 1 snd-via82xx
snd-mpu401-uart 5920 1 snd-via82xx
snd-rawmidi 19648 1 snd-mpu401-uart
snd-seq-device 6796 4 snd-seq-dummy,snd-seq-oss,snd-seq,snd-rawmidi
snd 46980 11 snd-seq-oss,snd-seq,snd-pcm-oss,snd-mixer-oss,snd-via82xx,snd-ac97-codec,snd-pcm,snd-timer,snd-mpu401-uart,snd-rawmidi,snd-seq-device
soundcore 7104 1 snd
lp 9864 0
af_packet 16232 2
floppy 54736 0
video 13892 0
thermal 10600 0
tc1100-wmi 5188 0
processor 18164 1 thermal
fan 3108 0
container 3040 0
button 4880 0
battery 7460 0
ac 3300 0
via-rhine 19364 0
mii 4224 1 via-rhine
ide-cd 36772 0
loop 13544 0
nls_cp850 4544 3
vfat 11200 3
fat 35964 1 vfat
nls_iso8859-15 4288 4
ntfs 205368 1
supermount 32660 1
reiserfs 261876 2
pcspkr 3076 0
sd_mod 15920 2
imm 10952 0
parport_pc 31652 2
ppa 10472 1
parport 31624 4 lp,imm,parport_pc,ppa
nvidia 3916668 12
via-agp 7424 1
agpgart 28264 2 nvidia,via-agp
sg 34268 0
scsi_mod 115784 4 sd_mod,imm,ppa,sg
tsdev 6016 0
evdev 7744 0
usbmouse 4640 0
ehci-hcd 28648 0
usbhid 43712 0
usblp 10784 0
uhci-hcd 28944 0
usbcore 106008 7 wacom,usbmouse,ehci-hcd,usbhid,usblp,uhci-hcd
ext3 123304 1
jbd 48344 1 ext3
-------------- next part --------------
APIC address 0xfee00000
ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
Processor #0 6:8 APIC version 16
ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1])
ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
IOAPIC[0]: apic_id 2, version 3, address 0xfec00000, GSI 0-23
ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl edge)
ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 low level)
ACPI: IRQ0 used by override.
ACPI: IRQ2 used by override.
ACPI: IRQ9 used by override.
Enabling APIC mode: Flat. Using 1 I/O APICs
Using ACPI (MADT) for SMP configuration information
Allocating PCI resources starting at 10000000 (gap: 10000000:eec00000)
Built 1 zonelists
mapped APIC to ffffd000 (fee00000)
mapped IOAPIC to ffffc000 (fec00000)
Initializing CPU#0
Kernel command line: root=/dev/hda9 resume=/dev/hda8 splash=silent vga=788
bootsplash: silent mode.
PID hash table entries: 1024 (order: 10, 16384 bytes)
Detected 1467.420 MHz processor.
Using pmtmr for high-res timesource
Console: colour dummy device 80x25
Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
Memory: 255124k/262128k available (2295k kernel code, 6344k reserved, 686k data, 264k init, 0k highmem, 0k BadRAM)
Checking if this processor honours the WP bit even in supervisor mode... Ok.
Calibrating delay loop... 2908.16 BogoMIPS (lpj=1454080)
Mount-cache hash table entries: 512 (order: 0, 4096 bytes)
CPU: After generic identify, caps: 0383fbff c1c3fbff 00000000 00000000 00000000 00000000 00000000
CPU: After vendor identify, caps: 0383fbff c1c3fbff 00000000 00000000 00000000 00000000 00000000
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 256K (64 bytes/line)
CPU: After all inits, caps: 0383fbff c1c3fbff 00000000 00000020 00000000 00000000 00000000
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
CPU: AMD Athlon(TM) XP 1700+ stepping 01
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Checking 'hlt' instruction... OK.
ACPI: Looking for DSDT in initrd... not found.
ENABLING IO-APIC IRQs
..TIMER: vector=0x31 pin1=2 pin2=-1
checking if image is initramfs...it isn't (no cpio magic); looks like an initrd
Freeing initrd memory: 217k freed
NET: Registered protocol family 16
PCI: PCI BIOS revision 2.10 entry at 0xf1960, last bus=1
PCI: Using configuration type 1
mtrr: v2.0 (20020519)
ACPI: Subsystem revision 20050211
ACPI: Interpreter enabled
ACPI: Using IOAPIC for interrupt routing
ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 9 10 *11 12)
ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 9 10 11 12) *0, disabled.
ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 6 7 9 10 11 12) *0, disabled.
ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 7 9 10 11 12) *0, disabled.
ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 9 *10 11 12)
ACPI: PCI Interrupt Link [LNKF] (IRQs *3 4 5 6 7 9 10 11 12)
ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 *5 6 7 10 11 12 14 15)
ACPI: PCI Root Bridge [PCI0] (00:00)
PCI: Probing PCI hardware (bus 00)
PCI: Via IRQ fixup
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCI1._PRT]
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI init
pnp: PnP ACPI: found 13 devices
PnPBIOS: Disabled
PCI: Using ACPI for IRQ routing
** PCI interrupts are no longer routed automatically. If this
** causes a device to stop working, it is probably because the
** driver failed to call pci_enable_device(). As a temporary
** workaround, the "pci=routeirq" argument restores the old
** behavior. If this argument makes the device work again,
** please email the output of "lspci" to bjorn.helgaas at hp.com
** so I can fix the driver.
pnp: 00:01: ioport range 0xe400-0xe47f could not be reserved
pnp: 00:01: ioport range 0xe800-0xe81f has been reserved
pnp: 00:0c: ioport range 0x290-0x297 has been reserved
pnp: 00:0c: ioport range 0x370-0x375 has been reserved
Simple Boot Flag at 0x3a set to 0x1
apm: BIOS version 1.2 Flags 0x03 (Driver version 1.16ac)
apm: overridden by ACPI.
audit: initializing netlink socket (disabled)
audit(1130703690.112:0): initialized
inotify device minor=63
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
devfs: 2004-01-31 Richard Gooch (rgooch at atnf.csiro.au)
devfs: boot_options: 0x0
Initializing Cryptographic API
vesafb: framebuffer at 0xf0000000, mapped to 0xd0880000, using 3750k, total 65536k
vesafb: mode is 800x600x16, linelength=1600, pages=2
vesafb: protected mode interface info at c000:e4e0
vesafb: scrolling: redraw
vesafb: Truecolor: size=0:5:6:5, shift=0:11:5:0
bootsplash 3.1.6-2004/03/31: looking for picture...<6> silentjpeg size 35024 bytes,<6>...found (800x600, 34976 bytes, v3).
Console: switching to colour frame buffer device 92x32
fb0: VESA VGA frame buffer device
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
Real Time Clock Driver v1.12
serio: i8042 AUX port at 0x60,0x64 irq 12
serio: i8042 KBD port at 0x60,0x64 irq 1
Serial: 8250/16550 driver $Revision: 1.90 $ 8 ports, IRQ sharing enabled
ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered
RAMDISK driver initialized: 16 RAM disks of 32000K size 1024 blocksize
pktcdvd: v0.2.0a 2004-07-14 Jens Axboe (axboe at suse.de) and petero2 at telia.com
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
VP_IDE: IDE controller at PCI slot 0000:00:11.1
ACPI: PCI interrupt 0000:00:11.1[A]: no GSI
VP_IDE: chipset revision 6
VP_IDE: not 100% native mode: will probe irqs later
VP_IDE: VIA vt8235 (rev 00) IDE UDMA133 controller on pci0000:00:11.1
ide0: BM-DMA at 0xb800-0xb807, BIOS settings: hda:DMA, hdb:pio
ide1: BM-DMA at 0xb808-0xb80f, BIOS settings: hdc:DMA, hdd:DMA
Probing IDE interface ide0...
hda: Maxtor 6Y080L0, ATA DISK drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
Probing IDE interface ide1...
hdc: ST340014A, ATA DISK drive
hdd: SAMSUNG CD-ROM SC-152A, ATAPI CD/DVD-ROM drive
ide1 at 0x170-0x177,0x376 on irq 15
hda: max request size: 128KiB
hda: 160086528 sectors (81964 MB) w/2048KiB Cache, CHS=65535/16/63, UDMA(133)
hda: cache flushes supported
/dev/ide/host0/bus0/target0/lun0: p1 p2 < p5 p6 p7 p8 p9 p10 p11 p12 > p3
hdc: max request size: 1024KiB
hdc: 78165360 sectors (40020 MB) w/2048KiB Cache, CHS=16383/255/63, UDMA(100)
hdc: cache flushes supported
/dev/ide/host0/bus1/target0/lun0: p1 p2 < p5 >
mice: PS/2 mouse device common for all mice
input: AT Translated Set 2 keyboard on isa0060/serio0
md: md driver 0.90.1 MAX_MD_DEVS=256, MD_SB_DISKS=27
NET: Registered protocol family 2
IP: routing cache hash table of 2048 buckets, 16Kbytes
TCP established hash table entries: 16384 (order: 5, 131072 bytes)
TCP bind hash table entries: 16384 (order: 4, 65536 bytes)
TCP: Hash tables configured (established 16384 bind 16384)
NET: Registered protocol family 1
ACPI wakeup devices:
PCI0 PCI1 USB0 USB1 USB2 SU20 SLAN
ACPI: (supports S0 S1 S4 S5)
BIOS EDD facility v0.16 2004-Jun-25, 2 devices found
devfs_mk_dev: could not append to parent for md/0
md: Autodetecting RAID arrays.
md: autorun ...
md: ... autorun DONE.
RAMDISK: Compressed image found at block 0
VFS: Mounted root (ext2 filesystem).
kjournald starting. Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
Freeing unused kernel memory: 264k freed
usbcore: registered new driver usbfs
usbcore: registered new driver hub
USB Universal Host Controller Interface driver v2.2
ACPI: PCI interrupt 0000:00:10.0[A] -> GSI 21 (level, low) -> IRQ 21
uhci_hcd 0000:00:10.0: UHCI Host Controller
uhci_hcd 0000:00:10.0: irq 21, io base 0xd800
uhci_hcd 0000:00:10.0: new USB bus registered, assigned bus number 1
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
ACPI: PCI interrupt 0000:00:10.1[B] -> GSI 21 (level, low) -> IRQ 21
uhci_hcd 0000:00:10.1: UHCI Host Controller
uhci_hcd 0000:00:10.1: irq 21, io base 0xd400
uhci_hcd 0000:00:10.1: new USB bus registered, assigned bus number 2
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
ACPI: PCI interrupt 0000:00:10.2[C] -> GSI 21 (level, low) -> IRQ 21
uhci_hcd 0000:00:10.2: UHCI Host Controller
uhci_hcd 0000:00:10.2: irq 21, io base 0xd000
uhci_hcd 0000:00:10.2: new USB bus registered, assigned bus number 3
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
usb 1-2: new full speed USB device using uhci_hcd and address 2
usb 2-1: new full speed USB device using uhci_hcd and address 2
usb 2-2: new low speed USB device using uhci_hcd and address 3
drivers/usb/class/usblp.c: usblp0: USB Bidirectional printer dev 2 if 0 alt 0 proto 2 vid 0x04A9 pid 0x105D
usbcore: registered new driver usblp
drivers/usb/class/usblp.c: v0.13: USB Printer Device Class driver
usbcore: registered new driver hiddev
ACPI: PCI interrupt 0000:00:10.3[D] -> GSI 21 (level, low) -> IRQ 21
ehci_hcd 0000:00:10.3: EHCI Host Controller
ehci_hcd 0000:00:10.3: irq 21, pci mem 0xed800000
ehci_hcd 0000:00:10.3: new USB bus registered, assigned bus number 4
ehci_hcd 0000:00:10.3: USB 2.0 initialized, EHCI 1.00, driver 10 Dec 2004
drivers/usb/input/hid-core.c: ctrl urb status -71 received
input: USB HID v1.10 Mouse [Logitech] on usb-0000:00:10.1-2
usbcore: registered new driver usbhid
drivers/usb/input/hid-core.c: v2.0:USB HID core driver
usb 1-2: USB disconnect, address 2
drivers/usb/class/usblp.c: usblp0: removed
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 6 ports detected
usbcore: registered new driver usbmouse
drivers/usb/input/usbmouse.c: v1.6:USB HID Boot Protocol mouse driver
usb 2-1: USB disconnect, address 2
usb 2-2: USB disconnect, address 3
ts: Compaq touchscreen protocol output
usb 1-2: new full speed USB device using uhci_hcd and address 3
drivers/usb/class/usblp.c: usblp0: USB Bidirectional printer dev 3 if 0 alt 0 proto 2 vid 0x04A9 pid 0x105D
usb 2-1: new full speed USB device using uhci_hcd and address 4
usb 2-2: new low speed USB device using uhci_hcd and address 5
input: USB HID v1.10 Mouse [Logitech USB-PS/2 Optical Mouse] on usb-0000:00:10.1-2
EXT3 FS on hda9, internal journal
SCSI subsystem initialized
Adding 257000k swap on /dev/hda8. Priority:-1 extents:1
Linux agpgart interface v0.100 (c) Dave Jones
agpgart: Detected VIA KT400/KT400A/KT600 chipset
agpgart: Maximum main memory to use for agp memory: 203M
agpgart: AGP aperture is 64M @ 0xf8000000
nvidia: module license 'NVIDIA' taints kernel.
ACPI: PCI interrupt 0000:01:00.0[A] -> GSI 16 (level, low) -> IRQ 16
NVRM: loading NVIDIA Linux x86 NVIDIA Kernel Module 1.0-7174 Tue Mar 22 06:44:39 PST 2005
ppa: Version 2.07 (for Linux 2.4.x)
parport: PnPBIOS parport detected.
parport0: PC-style at 0x378 (0x778), irq 7, dma 3 [PCSPP,TRISTATE,COMPAT,ECP,DMA]
parport0: Printer, OKI DATA CORP OKI OKIPAGE 4w
ppa: Found device at ID 6, Attempting to use EPP 32 bit
ppa: Communication established with ID 6 using EPP 32 bit
scsi0 : Iomega VPI0 (ppa) interface
Vendor: IOMEGA Model: ZIP 100 Rev: J.03
Type: Direct-Access ANSI SCSI revision: 02
Attached scsi generic sg0 at scsi0, channel 0, id 6, lun 0, type 0
imm: Version 2.05 (for Linux 2.4.0)
SCSI device sda: 196608 512-byte hdwr sectors (101 MB)
sda: Write Protect is off
sda: Mode Sense: 25 00 00 08
sda: cache data unavailable
sda: assuming drive cache: write through
SCSI device sda: 196608 512-byte hdwr sectors (101 MB)
sda: Write Protect is off
sda: Mode Sense: 25 00 00 08
sda: cache data unavailable
sda: assuming drive cache: write through
/dev/scsi/host0/bus0/target6/lun0:<6>input: PC Speaker
p4
Attached scsi removable disk sda at scsi0, channel 0, id 6, lun 0
ReiserFS: hda10: found reiserfs format "3.6" with standard journal
ReiserFS: hda10: using ordered data mode
ReiserFS: hda10: journal params: device hda10, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30
ReiserFS: hda10: checking transaction log (hda10)
ReiserFS: hda10: Using r5 hash to sort names
Supermount version 2.0.4 for kernel 2.6
ntfs: Ignoring new-style parameters in presence of obsolete ones
NTFS driver 2.1.22 [Flags: R/O DEBUG MODULE].
NTFS volume version 3.1.
ReiserFS: hda7: found reiserfs format "3.6" with standard journal
ReiserFS: hda7: using ordered data mode
ReiserFS: hda7: journal params: device hda7, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30
ReiserFS: hda7: checking transaction log (hda7)
ReiserFS: hda7: Using r5 hash to sort names
loop: loaded (max 8 devices)
hdd: ATAPI 52X CD-ROM drive, 128kB Cache, DMA
Uniform CD-ROM driver Revision: 3.20
via-rhine.c:v1.10-LK1.2.0-2.6 June-10-2004 Written by Donald Becker
ACPI: PCI interrupt 0000:00:12.0[A] -> GSI 23 (level, low) -> IRQ 23
eth0: VIA Rhine II at 0x1b400, 00:11:2f:ca:ea:d3, IRQ 23.
eth0: MII PHY found at address 1, status 0x786d advertising 01e1 Link 45e1.
ACPI: Power Button (FF) [PWRF]
Floppy drive(s): fd0 is 1.44M
FDC 0 is a post-1991 82077
NET: Registered protocol family 17
eth0: link up, 100Mbps, full-duplex, lpa 0x45E1
lp0: using parport0 (interrupt-driven).
lp0: console ready
lp0: ECP mode
lp0: ECP mode
lp0: ECP mode
ACPI: PCI interrupt 0000:00:11.5[C] -> GSI 22 (level, low) -> IRQ 22
PCI: Setting latency timer of device 0000:00:11.5 to 64
codec_read: codec 0 is not valid [0x107e5370]
codec_read: codec 0 is not valid [0x107e5370]
codec_read: codec 0 is not valid [0x107e5370]
codec_read: codec 0 is not valid [0x107e5370]
NET: Registered protocol family 10
Disabled Privacy Extensions on device c03b26e0(lo)
IPv6 over IPv4 tunneling driver
ip_tables: (C) 2000-2002 Netfilter core team
ip_conntrack version 2.1 (2047 buckets, 16376 max) - 248 bytes per conntrack
agpgart: Found an AGP 3.5 compliant device at 0000:00:00.0.
agpgart: X passes broken AGP3 flags (1f00000c). Fixed.
agpgart: Putting AGP V3 device at 0000:00:00.0 into 4x mode
agpgart: Putting AGP V3 device at 0000:01:00.0 into 4x mode
agpgart: Found an AGP 3.5 compliant device at 0000:00:00.0.
agpgart: X passes broken AGP3 flags (1f00000c). Fixed.
agpgart: Putting AGP V3 device at 0000:00:00.0 into 4x mode
agpgart: Putting AGP V3 device at 0000:01:00.0 into 4x mode
usbcore: registered new driver wacom
drivers/usb/input/wacom.c: v1.30:USB Wacom Graphire and Wacom Intuos tablet driver
eth0: no IPv6 routers present
lp0: ECP mode
bootsplash 3.1.6-2004/03/31: looking for picture...<6>...found (800x600, 10640 bytes, v3).
bootsplash: status on console 0 changed to on
bootsplash 3.1.6-2004/03/31: looking for picture...<6>...found (800x600, 10640 bytes, v3).
bootsplash: status on console 1 changed to on
bootsplash 3.1.6-2004/03/31: looking for picture...<6>...found (800x600, 10640 bytes, v3).
bootsplash: status on console 2 changed to on
bootsplash 3.1.6-2004/03/31: looking for picture...<6>...found (800x600, 10640 bytes, v3).
bootsplash: status on console 3 changed to on
bootsplash 3.1.6-2004/03/31: looking for picture...<6>...found (800x600, 10640 bytes, v3).
bootsplash: status on console 4 changed to on
bootsplash 3.1.6-2004/03/31: looking for picture...<6>...found (800x600, 10640 bytes, v3).
bootsplash: status on console 5 changed to on
More information about the Sclug
mailing list